Xin chào ! Nếu đây là lần đầu tiên bạn đến với diễn đàn, xin vui lòng danh ra một phút bấm vào đây để đăng kí và tham gia thảo luận cùng VnPro.

Announcement

Collapse
No announcement yet.

Hỏi về cấu hình portchannel.gấp lắm

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Hỏi về cấu hình portchannel.gấp lắm

    em đang cấu hình port-channel giữa 2 con : 1 con Cisco 3650 và 1 con planet 24000. Con Cisco hoạt động ở Layer 3.làm Routing.Nhưng khi em cấu hình xong thì nó không cho VLAN đi qua (Không ping đc tí gì luôn).Ở đây em cấu hình gộp 4 đường.Em đã trunk triếc các thứ đủ cả ( khi rút 3 đường để lại 1 đường thì lại thông được):105::105::105::105:.Em đã thử khi không cấu hình VLAN chỉ mỗi switching không thì lại chạy ngon( đo bandwidth thấy ngon )
    Đây là cấu hình của em.Mọi người xem giúp em nhé.đang gấp lém
    Trên con 3650

    interface Port-channel1
    switchport trunk encapsulation dot1q
    switchport mode trunk


    :interface FastEthernet0/14
    switchport trunk encapsulation dot1q
    switchport mode trunk
    channel-protocol pagp
    channel-group 1 mode desirable
    !
    interface FastEthernet0/15
    switchport trunk encapsulation dot1q
    switchport mode trunk
    channel-protocol pagp
    channel-group 1 mode desirable
    !
    interface FastEthernet0/16
    switchport trunk encapsulation dot1q
    switchport mode trunk
    channel-protocol pagp
    channel-group 1 mode desirable
    !
    interface FastEthernet0/17
    switchport trunk encapsulation dot1q
    switchport mode trunk
    channel-protocol pagp
    channel-group 1 mode desirable


    Switch#sho ip int bri
    Interface IP-Address OK? Method Status Protocol
    Vlan1 192.168.2.202 YES manual up up
    Vlan2 10.2.2.1 YES manual up up
    Vlan3 10.3.3.1 YES manual up up


    Port-channel1 unassigned YES unset down down em đang thắc mắc chỗ này tại sao nó lại down trong khi em đã no shut.các cổng thành viên thì lại up@-)@-)
    Switch#show etherchannel de
    Switch#show etherchannel detail
    Channel-group listing:
    ----------------------

    Group: 1
    ----------
    Group state = L2
    Ports: 4 Maxports = 8
    Port-channels: 1 Max Port-channels = 1
    Protocol: PAgP
    Ports in the group:
    -------------------
    Port: Fa0/14
    ------------

    Port state = Down Not-in-Bndl
    Channel group = 1 Mode = Desirable-Sl Gcchange = 0
    Port-channel = null GC = 0x00000000 Pseudo port-channel = Po1
    Port index = 0 Load = 0x00 Protocol = PAgP

    Flags: S - Device is sending Slow hello. C - Device is in Consistent state.
    A - Device is in Auto mode. P - Device learns on physical port.
    d - PAgP is down.
    Timers: H - Hello timer is running. Q - Quit timer is running.
    S - Switching timer is running. I - Interface timer is running.

    Local information:
    Hello Partner PAgP Learning Group
    Port Flags State Timers Interval Count Priority Method Ifindex
    Fa0/14 d U1/S1 1s 0 128 Any 0

    Age of the port in the current state: 00d:00h:11m:22s

    Port: Fa0/15
    ------------

    Port state = Down Not-in-Bndl
    Channel group = 1 Mode = Desirable-Sl Gcchange = 0
    Port-channel = null GC = 0x00000000 Pseudo port-channel = Po1
    Port index = 0 Load = 0x00 Protocol = PAgP

    Flags: S - Device is sending Slow hello. C - Device is in Consistent state.
    A - Device is in Auto mode. P - Device learns on physical port.
    d - PAgP is down.
    Timers: H - Hello timer is running. Q - Quit timer is running.
    S - Switching timer is running. I - Interface timer is running.

    Local information:
    Hello Partner PAgP Learning Group
    Port Flags State Timers Interval Count Priority Method Ifindex
    Fa0/15 d U1/S1 1s 0 128 Any 0

    Age of the port in the current state: 00d:00h:11m:26s

    Port: Fa0/16
    ------------

    Port state = Down Not-in-Bndl
    Channel group = 1 Mode = Desirable-Sl Gcchange = 0
    Port-channel = null GC = 0x00000000 Pseudo port-channel = Po1
    Port index = 0 Load = 0x00 Protocol = PAgP

    Flags: S - Device is sending Slow hello. C - Device is in Consistent state.
    A - Device is in Auto mode. P - Device learns on physical port.
    d - PAgP is down.
    Timers: H - Hello timer is running. Q - Quit timer is running.
    S - Switching timer is running. I - Interface timer is running.

    Local information:
    Hello Partner PAgP Learning Group
    Port Flags State Timers Interval Count Priority Method Ifindex
    Fa0/16 d U1/S1 1s 0 128 Any 0

    Age of the port in the current state: 00d:00h:11m:30s

    Port: Fa0/17
    ------------

    Port state = Up Sngl-port-Bndl Mstr Not-in-Bndl
    Channel group = 1 Mode = Desirable-Sl Gcchange = 0
    Port-channel = null GC = 0x00010001 Pseudo port-channel = Po1
    Port index = 0 Load = 0x00 Protocol = PAgP

    Flags: S - Device is sending Slow hello. C - Device is in Consistent state.
    A - Device is in Auto mode. P - Device learns on physical port.
    d - PAgP is down.
    Timers: H - Hello timer is running. Q - Quit timer is running.
    S - Switching timer is running. I - Interface timer is running.

    Local information:
    Hello Partner PAgP Learning Group
    Port Flags State Timers Interval Count Priority Method Ifindex
    Fa0/17 U4/S4 H 30s 0 128 Any 13

    Age of the port in the current state: 00d:00h:23m:03s

    Port-channels in the group:
    ---------------------------

    Port-channel: Po1
    ------------

    Age of the Port-channel = 00d:00h:38m:32s
    Logical slot/port = 1/0 Number of ports = 0
    GC = 0x00000000 HotStandBy port = null
    Port state = Port-channel Ag-Not-Inuse
    Protocol = PAgP

    Switch#show int trunk

    Port Mode Encapsulation Status Native vlan
    Fa0/14 on 802.1q trunking 1
    Fa0/15 on 802.1q trunking 1
    Fa0/16 on 802.1q trunking 1
    Fa0/17 on 802.1q trunking 1

    Port Vlans allowed on trunk
    Fa0/14 1-4094
    Fa0/15 1-4094
    Fa0/16 1-4094
    Fa0/17 1-4094

    Port Vlans allowed and active in management domain
    Fa0/14 1-3
    Fa0/15 1-3
    Fa0/16 1-3
    Fa0/17 1-3

    Port Vlans in spanning tree forwarding state and not pruned
    Fa0/14 none
    Fa0/15 none
    Fa0/16 none
    Fa0/17 1-3

    Switch#show int port 1
    Port-channel1 is down, line protocol is down (notconnect)
    Hardware is EtherChannel, address is 0000.0000.0000 (bia 0000.0000.0000)
    MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
    reliability 255/255, txload 1/255, rxload 1/255
    Encapsulation ARPA, loopback not set
    Auto-duplex, Auto-speed, media type is 10/100BaseTX
    input flow-control is off, output flow-control is unsupported
    ARP type: ARPA, ARP Timeout 04:00:00
    Last input never, output never, output hang never
    Last clearing of "show interface" counters never
    Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
    Queueing strategy: fifo
    Output queue: 0/40 (size/max)
    5 minute input rate 0 bits/sec, 0 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    0 packets input, 0 bytes, 0 no buffer
    Received 0 broadcasts (0 multicast)
    0 runts, 0 giants, 0 throttles
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
    0 watchdog, 0 multicast, 0 pause input
    0 input packets with dribble condition detected
    0 packets output, 0 bytes, 0 underruns
    0 output errors, 0 collisions, 1 interface resets
    0 babbles, 0 late collision, 0 deferred
    0 lost carrier, 0 no carrier, 0 PAUSE output
    0 output buffer failures, 0 output buffers swapped out

    Trên con planet cấu hình bằng giao diên web nên em chưa kịp chụp vào.Các pro trả lời nhanh giúp em nhé.em cảm ơn lắm lắm....:|

  • #2
    Originally posted by dinhvietbk View Post
    em đang cấu hình port-channel giữa 2 con : 1 con Cisco 3650 và 1 con planet 24000. Con Cisco hoạt động ở Layer 3.làm Routing.Nhưng khi em cấu hình xong thì nó không cho VLAN đi qua (Không ping đc tí gì luôn).Ở đây em cấu hình gộp 4 đường.Em đã trunk triếc các thứ đủ cả ( khi rút 3 đường để lại 1 đường thì lại thông được):105::105::105::105:.Em đã thử khi không cấu hình VLAN chỉ mỗi switching không thì lại chạy ngon( đo bandwidth thấy ngon )
    Đây là cấu hình của em.Mọi người xem giúp em nhé.đang gấp lém
    Trên con 3650

    interface Port-channel1
    switchport trunk encapsulation dot1q
    switchport mode trunk


    :interface FastEthernet0/14
    switchport trunk encapsulation dot1q
    switchport mode trunk
    channel-protocol pagp
    channel-group 1 mode desirable
    !
    interface FastEthernet0/15
    switchport trunk encapsulation dot1q
    switchport mode trunk
    channel-protocol pagp
    channel-group 1 mode desirable
    !
    interface FastEthernet0/16
    switchport trunk encapsulation dot1q
    switchport mode trunk
    channel-protocol pagp
    channel-group 1 mode desirable
    !
    interface FastEthernet0/17
    switchport trunk encapsulation dot1q
    switchport mode trunk
    channel-protocol pagp
    channel-group 1 mode desirable


    Switch#sho ip int bri
    Interface IP-Address OK? Method Status Protocol
    Vlan1 192.168.2.202 YES manual up up
    Vlan2 10.2.2.1 YES manual up up
    Vlan3 10.3.3.1 YES manual up up


    Port-channel1 unassigned YES unset down down em đang thắc mắc chỗ này tại sao nó lại down trong khi em đã no shut.các cổng thành viên thì lại up@-)@-)
    Switch#show etherchannel de
    Switch#show etherchannel detail
    Channel-group listing:
    ----------------------

    Group: 1
    ----------
    Group state = L2
    Ports: 4 Maxports = 8
    Port-channels: 1 Max Port-channels = 1
    Protocol: PAgP
    Ports in the group:
    -------------------
    Port: Fa0/14
    ------------

    Port state = Down Not-in-Bndl
    Channel group = 1 Mode = Desirable-Sl Gcchange = 0
    Port-channel = null GC = 0x00000000 Pseudo port-channel = Po1
    Port index = 0 Load = 0x00 Protocol = PAgP

    Flags: S - Device is sending Slow hello. C - Device is in Consistent state.
    A - Device is in Auto mode. P - Device learns on physical port.
    d - PAgP is down.
    Timers: H - Hello timer is running. Q - Quit timer is running.
    S - Switching timer is running. I - Interface timer is running.

    Local information:
    Hello Partner PAgP Learning Group
    Port Flags State Timers Interval Count Priority Method Ifindex
    Fa0/14 d U1/S1 1s 0 128 Any 0

    Age of the port in the current state: 00d:00h:11m:22s

    Port: Fa0/15
    ------------

    Port state = Down Not-in-Bndl
    Channel group = 1 Mode = Desirable-Sl Gcchange = 0
    Port-channel = null GC = 0x00000000 Pseudo port-channel = Po1
    Port index = 0 Load = 0x00 Protocol = PAgP

    Flags: S - Device is sending Slow hello. C - Device is in Consistent state.
    A - Device is in Auto mode. P - Device learns on physical port.
    d - PAgP is down.
    Timers: H - Hello timer is running. Q - Quit timer is running.
    S - Switching timer is running. I - Interface timer is running.

    Local information:
    Hello Partner PAgP Learning Group
    Port Flags State Timers Interval Count Priority Method Ifindex
    Fa0/15 d U1/S1 1s 0 128 Any 0

    Age of the port in the current state: 00d:00h:11m:26s

    Port: Fa0/16
    ------------

    Port state = Down Not-in-Bndl
    Channel group = 1 Mode = Desirable-Sl Gcchange = 0
    Port-channel = null GC = 0x00000000 Pseudo port-channel = Po1
    Port index = 0 Load = 0x00 Protocol = PAgP

    Flags: S - Device is sending Slow hello. C - Device is in Consistent state.
    A - Device is in Auto mode. P - Device learns on physical port.
    d - PAgP is down.
    Timers: H - Hello timer is running. Q - Quit timer is running.
    S - Switching timer is running. I - Interface timer is running.

    Local information:
    Hello Partner PAgP Learning Group
    Port Flags State Timers Interval Count Priority Method Ifindex
    Fa0/16 d U1/S1 1s 0 128 Any 0

    Age of the port in the current state: 00d:00h:11m:30s

    Port: Fa0/17
    ------------

    Port state = Up Sngl-port-Bndl Mstr Not-in-Bndl
    Channel group = 1 Mode = Desirable-Sl Gcchange = 0
    Port-channel = null GC = 0x00010001 Pseudo port-channel = Po1
    Port index = 0 Load = 0x00 Protocol = PAgP

    Flags: S - Device is sending Slow hello. C - Device is in Consistent state.
    A - Device is in Auto mode. P - Device learns on physical port.
    d - PAgP is down.
    Timers: H - Hello timer is running. Q - Quit timer is running.
    S - Switching timer is running. I - Interface timer is running.

    Local information:
    Hello Partner PAgP Learning Group
    Port Flags State Timers Interval Count Priority Method Ifindex
    Fa0/17 U4/S4 H 30s 0 128 Any 13

    Age of the port in the current state: 00d:00h:23m:03s

    Port-channels in the group:
    ---------------------------

    Port-channel: Po1
    ------------

    Age of the Port-channel = 00d:00h:38m:32s
    Logical slot/port = 1/0 Number of ports = 0
    GC = 0x00000000 HotStandBy port = null
    Port state = Port-channel Ag-Not-Inuse
    Protocol = PAgP

    Switch#show int trunk

    Port Mode Encapsulation Status Native vlan
    Fa0/14 on 802.1q trunking 1
    Fa0/15 on 802.1q trunking 1
    Fa0/16 on 802.1q trunking 1
    Fa0/17 on 802.1q trunking 1

    Port Vlans allowed on trunk
    Fa0/14 1-4094
    Fa0/15 1-4094
    Fa0/16 1-4094
    Fa0/17 1-4094

    Port Vlans allowed and active in management domain
    Fa0/14 1-3
    Fa0/15 1-3
    Fa0/16 1-3
    Fa0/17 1-3

    Port Vlans in spanning tree forwarding state and not pruned
    Fa0/14 none
    Fa0/15 none
    Fa0/16 none
    Fa0/17 1-3

    Switch#show int port 1
    Port-channel1 is down, line protocol is down (notconnect)
    Hardware is EtherChannel, address is 0000.0000.0000 (bia 0000.0000.0000)
    MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
    reliability 255/255, txload 1/255, rxload 1/255
    Encapsulation ARPA, loopback not set
    Auto-duplex, Auto-speed, media type is 10/100BaseTX
    input flow-control is off, output flow-control is unsupported
    ARP type: ARPA, ARP Timeout 04:00:00
    Last input never, output never, output hang never
    Last clearing of "show interface" counters never
    Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
    Queueing strategy: fifo
    Output queue: 0/40 (size/max)
    5 minute input rate 0 bits/sec, 0 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    0 packets input, 0 bytes, 0 no buffer
    Received 0 broadcasts (0 multicast)
    0 runts, 0 giants, 0 throttles
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
    0 watchdog, 0 multicast, 0 pause input
    0 input packets with dribble condition detected
    0 packets output, 0 bytes, 0 underruns
    0 output errors, 0 collisions, 1 interface resets
    0 babbles, 0 late collision, 0 deferred
    0 lost carrier, 0 no carrier, 0 PAUSE output
    0 output buffer failures, 0 output buffers swapped out

    Trên con planet cấu hình bằng giao diên web nên em chưa kịp chụp vào.Các pro trả lời nhanh giúp em nhé.em cảm ơn lắm lắm....:|
    Theo như anh nói thì một bên là Cisco, một bên là Planet [noncisco].
    Mà giao thức PAGP thì chỉ dành cho các thiết bị cisco.
    Vậy nếu có thể thì trên 3550 của anh cấu hình mode LACP. Vì đây là chuẩn mở.
    channel-protocol LACP

    Trên các dòng 2970, 3560, 4500, 6500 đều có mode LACP hết.
    Phạm Minh Tuấn

    Email : phamminhtuan@vnpro.org
    Yahoo : phamminhtuan_vnpro
    -----------------------------------------------------------------------------------------------
    Trung Tâm Tin Học VnPro
    149/1D Ung Văn Khiêm P25 Q.Bình thạnh TPHCM
    Tel : (08) 35124257 (5 lines)
    Fax: (08) 35124314

    Home page: http://www.vnpro.vn
    Support Forum: http://www.vnpro.org
    - Chuyên đào tạo quản trị mạng và hạ tầng Internet
    - Phát hành sách chuyên môn
    - Tư vấn và tuyển dụng nhân sự IT
    - Tư vấn thiết kế và hỗ trợ kỹ thuật hệ thống mạng

    Network channel: http://www.dancisco.com
    Blog: http://www.vnpro.org/blog

    Comment


    • #3
      HI, Thanks anh.Đúng là như thế thật.Cuối cùng em đã làm đc.hii may quá.:)

      Comment

      Working...
      X